Obiekt
Tytuł: Influence of nozzle geometry on fluid flow parameters
Współtwórca:
Tytuł publikacji grupowej:
Abstract:
The article discusses ways for optimization of a standard nozzle cup design to achieve a narrower paint flow. The analysis of a standard nozzle cup shows that distribution of air pressure is critically uneven both along the nozzle axis and in the radial direction. A decrease in pressure is about 45% at the distance of 2 mm from the front surface of the nozzle cup. ; Air pressure decreases about 40% at the distance of 2 mm from the nozzle axis in the radial direction. Air velocity decreases about 52% at the distance of 4 mm from nozzle surface but then the velocity stabilizes and decreases is about 59% at the distance of 10 mm from the nozzle surface in comparison to its magnitude on the nozzle surface. ; Six extra holes and a circular rim were added to the standard nozzle cup to obtain paint stream as narrow as possible. Also was modified inner surface of the nuzzle cup. Totally, four different components were analysed. The results show that with increasing the nozzle cone by fifteen or more degrees, the pressure distribution decreases. ; Most optimal solution has six small holes around the nozzle hole and a small rim covering all holes. In this case, pressure decreases only 3% in the axial direction and 4% in the radial direction at the distance of 2 mm from the front surface of the nozzle. Distribution of air velocity is still significant but its magnitude is about 35% ? 45% less than at the standard nozzle cup.
Wydawca:
Zielona Góra: Uniwersytet Zielonogórski
Format:
Identyfikator zasobu:
DOI:
Strony:
Źródło:
IJAME, volume 25, number 4 (2020)
Jezyk:
Licencja:
Licencja CC BY-NC-ND 4.0:
Prawa do dysponowania publikacją:
Biblioteka Uniwersytetu Zielonogórskiego
Kolekcje, do których przypisany jest obiekt:
- Repozytorium > Jednostki organizacyjne > Wydział Mechaniczny
- Repozytorium > Typy utworów > Artykuły
- Repozytorium > Czasopisma naukowe i serie wydawnicze UZ > International Journal of Applied Mechanics and Engineering (IJAME) > International Journal of Applied Mechanics and Engineering (IJAME) (2020)
Data ostatniej modyfikacji:
2023-07-06
Data dodania obiektu:
2023-02-27
Liczba wyświetleń treści obiektu:
81
Wszystkie dostępne wersje tego obiektu:
https://zbc.uz.zgora.pl/repozytorium/publication/78160
Wyświetl opis w formacie RDF:
Wyświetl opis w formacie OAI-PMH:
-
International Journal of Applied Mechanics and Engineering (IJAME)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 29 (2024)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 28 (2023)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 27 (2022)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 26 (2021)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 25 (2020)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 25, number 1 (2020)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 25, number 2 (2020)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 25, number 3 (2020)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 25, number 4 (2020)
- International Journal of Applied Mechanics and Engineering (IJAME), volume 25, number 4 (2020) - Contents
- Influence of heat generation/absorption on mixed convection flow behaviour in the presence of Lorentz forces in a vertical micro circular duct having time periodic boundary conditions: steady periodic regime
- A general study of fundamental solutions in aniotropicthermoelastic media with mass diffusion and voids
- Detection of vibrations defects in gas transportation plant based on input/output data analysis: gas turbine investigations
- A study on the stress concentration factor induced in double countersunk holes due to uniaxial tension
- Mathematical modeling of convective heat and mass transfer of a rotating nano-fluid bounded by stretching and stationary walls in a vertical conduit
- Elastic buckling analysis of uniaxially compressed CCCC stiffened isotropic plates
- The effect of modulation on heat transport by a weakly nonlinear thermal instability in the presence of applied magnetic field and internal heating
- Analytical model of the two-mass above resonance system of the eccentric-pendulum type vibration table
- Mechanical vapour compression refrigeration system: Review part 1: Environment challenge
- Mixed convective flow of unsteady hydromagnetic couple stress fluid through a vertical channel filled with porous medium
- Analysis of Magnetohydrodynamic (MHD) nanofluid flow with heat and mass transfer over a porous stretching sheet
- Transient heat and mass transfer of hydromagnetic effects on the flow past a porous medium with movable vertical permeablesheet
- A study on fractional order thermoelastic half space
- Experimental and numerical study on the effect of creep behavior on epoxy composites reinforced with yttrium oxide powder
- Influence of nozzle geometry on fluid flow parameters
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 25, number 1 (2020)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 24 (2019)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 23 (2018)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 22 (2017)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 21 (2016)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 20 (2015)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 19 (2014)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 18 (2013)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 29 (2024)
| Nazwa wydania | Data |
|---|---|
| Influence of nozzle geometry on fluid flow parameters | 2023-07-06 |
