Obiekt
Tytuł: Investigation of coated and uncoated carbide cutting tool wear in dry turning of en aw 2007 aluminum alloy
Autor:
Leksycki, Kamil ; Patil, Gauravkumar Himmatrao ; Małecka, Joanna ; Cagan, Cinar Suleyman ; Dąbrowski, Karol
Data wydania:
Typ zasobu:
Współtwórca:
Tytuł publikacji grupowej:
Abstract:
The automotive, aerospace and marine industries make extensive use of aluminum and its alloys to produce a wide variety of components. This prompts research work related to improving manufacturing processes using these materials. One of the main problems in this area is the durability of cutting tools. ; This article describes the results of tests on wear of the coated and uncoated carbide cutting tools during turning of EN AW 2007 aluminum alloy. The tests were carried out under dry conditions and at higher cutting speeds. On the face rake, the VBB indicator (average width of the flank wear) and on the rake face, the KB indicator (crater width on the rake face) were evaluated. Only for the uncoated insert, the break-in period, steady-state wear region and intensive wear were observed and the limited alue of the VBB indicator was obtained after 36 minutes of the tool life. ; The TiAlN+TiN coated insert, as well as TiCN achieved very short tool life periods of 16 and 24 minutes, respectively. Compared to the uncoated and the TiCN coated insert, a VBB increase of about 170% was obtained for the TiAlN+TiN coated insert after 16 minutes. In contrast, an increase in the VBB of almost 60% was obtained for the TiCN coated insert after 24 minutes, compared to the uncoated insert. ; Compared to the uncoated insert, an increase of 12.1% in the KB value was obtained for the TiCN coated insert, and 18.2% for the TiAlN+TiN coated insert. The main wear mechanism of the tested cutting inserts was the phenomenon of adhesion. Abrasion wear is observed on the surfaces of the TiAlN+TiN and TiCN coated inserts. The TiCN coated insert also showed coating delamination. The build-up edge (BUE) phenomenon is observed on the surfaces of the TiAlN+TiN coated and uncoated inserts.
Wydawca:
Zielona Góra: Uniwersytet Zielonogórski
Format:
Identyfikator zasobu:
DOI:
Strony:
Źródło:
IJAME, volume 29, number 3 (2024)
Jezyk:
Licencja:
Licencja CC BY-NC-ND 4.0:
Prawa do dysponowania publikacją:
Biblioteka Uniwersytetu Zielonogórskiego
Kolekcje, do których przypisany jest obiekt:
- Repozytorium > Jednostki organizacyjne > Wydział Mechaniczny
- Repozytorium > Typy utworów > Artykuły
- Repozytorium > Czasopisma naukowe i serie wydawnicze UZ > International Journal of Applied Mechanics and Engineering (IJAME)
- Repozytorium > Czasopisma naukowe i serie wydawnicze UZ > International Journal of Applied Mechanics and Engineering (IJAME) > International Journal of Applied Mechanics and Engineering (IJAME) (2024)
Data ostatniej modyfikacji:
2024-09-13
Data dodania obiektu:
2024-09-13
Liczba wyświetleń treści obiektu:
32
Wszystkie dostępne wersje tego obiektu:
https://zbc.uz.zgora.pl/repozytorium/publication/90109
Wyświetl opis w formacie RDF:
Wyświetl opis w formacie OAI-PMH:
-
International Journal of Applied Mechanics and Engineering (IJAME)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 29 (2024)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 29, number 1 (2024)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 29, number 2 (2024)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 29, number 3 (2024)
- International Journal of Applied Mechanics and Engineering (IJAME), volume 29, number 3 (2024) - Contents
- Comparing the performance of using a smart damper in a semi-active suspension instead of a traditional damper using MATLAB/simulink
- Effects of viscous dissipation over an unsteady stretching surface embedded in a porous medium with heat generation and thermal radiation
- Thermal diffusion and diffusion thermo effects on axi-symmetric boundary layer flow of nanofluid due to non-linear stretching sheet along the radial direction in presence of magnetic field
- Numerical study of adaptive grids for laminar flow in a suddenly expanding channel
- Investigation of coated and uncoated carbide cutting tool wear in dry turning of en aw 2007 aluminum alloy
- Start-off MHD electrokinetic Couette flow in an annulus: a Riemann-sum approximation approach
- Generation of entropy for MHD flow of Casson fluid past a vertical cone with Dufour effect
- The influence of Hall currents on unsteady-MHD heat transfer flowin a conducting channelcontaining two ionized fluids
- The effect of temperature on the vibration behaviour of laminated composite plates
- Heat transfer modelling in an annular disc under heating and cooling processes with stress analysis
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 29, number 4 (2024)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 29, number 1 (2024)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 28 (2023)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 27 (2022)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 26 (2021)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 25 (2020)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 24 (2019)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 23 (2018)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 22 (2017)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 21 (2016)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 20 (2015)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 19 (2014)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 18 (2013)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 29 (2024)
| Nazwa wydania | Data |
|---|---|
| Investigation of coated and uncoated carbide cutting tool wear in dry turning of en aw 2007 aluminum alloy | 2024-09-13 |
