Obiekt
Tytuł: Effect of ultrasonic peening on mechanical properties of low carbon steel AISI 1020 TIG welding joints process
Autor:
Mohammed Ali, Ghusoon Ridha ; Ridha, Ali Zuhair ; Sadeq, Dina Abbas ; Ebraheem, Ahmed Abdullah ; Atta, Amal Sadeq
Data wydania:
Typ zasobu:
Współtwórca:
Tytuł publikacji grupowej:
Abstract:
In this paper, the effect of ultrasonic peening surface treatment on the mechanical properties of TIG butt weld joints of low-carbon steel (AISI 1020) was studied. A single V-angle was made on sheets of metal used then welded at constant parameters, namely: current, voltage. ; Wire filler ER70S-3 with argon was used to obtain many butt welding joints. Some of them were subjected to ultrasonic peening at one, two, and three passes. The micro-hardness, microstructure, tensile, and bending were tested. ; The results show increases in the tensile strength after the welding process. The test results showed improvements in the tensile strength of the weldments in comparison to the base metal. ; On the other hand, the tensile strength decreased with the ultrasonic process. Nevertheless, the tensile strength increased at a high number of ultrasonic passes. On the contrary, the ultrasonic process enhanced the bending strength compared to the base metal, whereas the weldments ability to bend deteriorated.
Wydawca:
Zielona Góra: Uniwersytet Zielonogórski
Format:
Identyfikator zasobu:
DOI:
Strony:
Źródło:
IJAME, volume 27, number 4 (2022)
Jezyk:
Licencja:
Licencja CC BY-NC-ND 4.0:
Prawa do dysponowania publikacją:
Biblioteka Uniwersytetu Zielonogórskiego
Kolekcje, do których przypisany jest obiekt:
- Zielonogórska Biblioteka Cyfrowa > Repozytorium > Jednostki organizacyjne > Wydział Mechaniczny
- Zielonogórska Biblioteka Cyfrowa > Repozytorium > Typy utworów > Artykuły
- Zielonogórska Biblioteka Cyfrowa > Repozytorium > Czasopisma naukowe i serie wydawnicze UZ > International Journal of Applied Mechanics and Engineering (IJAME)
- Zielonogórska Biblioteka Cyfrowa > Repozytorium > Czasopisma naukowe i serie wydawnicze UZ > International Journal of Applied Mechanics and Engineering (IJAME) > International Journal of Applied Mechanics and Engineering (IJAME) (2022)
Data ostatniej modyfikacji:
2023-07-06
Data dodania obiektu:
2023-02-01
Liczba wyświetleń treści obiektu:
117
Wszystkie dostępne wersje tego obiektu:
https://zbc.uz.zgora.pl/publication/77337
Wyświetl opis w formacie RDF:
Wyświetl opis w formacie OAI-PMH:
-
International Journal of Applied Mechanics and Engineering (IJAME)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 29 (2024)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 28 (2023)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 27 (2022)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 27, number 1 (2022)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 27, number 2 (2022)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 27, number 3 (2022)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 27, number 4 (2022)
- International Journal of Applied Mechanics and Engineering (IJAME), volume 27, number 4 (2022) - Contents
- Joining of carbon steel AISI 1006 to aluminum alloy AA6061-T6 via friction spot joining technique
- Optimization of friction stir processing parameters of aluminum alloy reinforced with hybrid nanoparticles using the Taguchi method
- Strouhal number effects on dynamic boundary layer evolution over a wedge surface from initial flow to steady flow: analytical approach
- Influence of form defect on the mechanical behavior and stress intensity factor of shrink-fitted thick-walled cylinders
- Applying optimization techniques on cold-formed C-channel section under bending
- Heat transfer effects on carbon nanotubes along a moving flat plate subjected to uniform heat flux
- Visco-elastic fluid model in an inclined porous stenosed artery with slip effect and body acceleration
- The influence of thermal expansion on flow past an inclined accelerated sectional plate with persistent mass diffusion
- Computational approach to solving a layered behaviour differential equation with large delay using quadrature scheme
- Generalized plane waves in a rotating thermoelastic double porous solid
- Two-dimensional analysis of functionally graded thermoelastic microelongated solid
- An investigation of the suspension characteristics of the line model of the vehicle using the Taguchi method
- A method for comparison of large deflection in beams
- Effect of ultrasonic peening on mechanical properties of low carbon steel AISI 1020 TIG welding joints process
- Fabrication of a high wear resistance AA7075/AL2O3 composites via liquid metallurgy process
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 27, number 1 (2022)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 26 (2021)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 25 (2020)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 24 (2019)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 23 (2018)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 22 (2017)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 21 (2016)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 20 (2015)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 19 (2014)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 18 (2013)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 29 (2024)
| Nazwa wydania | Data |
|---|---|
| Effect of ultrasonic peening on mechanical properties of low carbon steel AISI 1020 TIG welding joints process | 2023-07-06 |
