Obiekt
Tytuł: Fabrication of a high wear resistance AA7075/AL2O3 composites via liquid metallurgy process
Autor:
Sivaraman, R. ; Jalil, Abduladheem Turki ; Aravindhan, Surendar ; Nan, Zhao ; Vini, M. Heydari ; Daneshmand, S.
Data wydania:
Typ zasobu:
Współtwórca:
Tytuł publikacji grupowej:
Abstract:
In the present study, AA7075/Al2O3 composites have been fabricated via liquid metallurgy process. AA7075 alloy and Al2O3 particles were taken as the base matrix and reinforcements, respectively. Then, contents of 3 and 6 wt. % of Al2O3 subdivisions were added into the AA7075 matrix. ; To improve wettability and distribution, reinforcement particles were pre-heated to a temperature of 550°C for each composite sample. A hardened EN32 steel disc as the counter face was used to evaluate the wear rate pin-on-disc. The results showed that the wear rate of the AA/Al2O3 composites was smaller than that of the monolithic AA7075 samples. Finally, the worn surfaces of samples were investigated by SEM.
Wydawca:
Zielona Góra: Uniwersytet Zielonogórski
Format:
Identyfikator zasobu:
DOI:
Strony:
Źródło:
IJAME, volume 27, number 4 (2022)
Jezyk:
Licencja:
Licencja CC BY-NC-ND 4.0:
Prawa do dysponowania publikacją:
Biblioteka Uniwersytetu Zielonogórskiego
Kolekcje, do których przypisany jest obiekt:
- Zielonogórska Biblioteka Cyfrowa > Repozytorium > Jednostki organizacyjne > Wydział Mechaniczny
- Zielonogórska Biblioteka Cyfrowa > Repozytorium > Typy utworów > Artykuły
- Zielonogórska Biblioteka Cyfrowa > Repozytorium > Czasopisma naukowe i serie wydawnicze UZ > International Journal of Applied Mechanics and Engineering (IJAME)
- Zielonogórska Biblioteka Cyfrowa > Repozytorium > Czasopisma naukowe i serie wydawnicze UZ > International Journal of Applied Mechanics and Engineering (IJAME) > International Journal of Applied Mechanics and Engineering (IJAME) (2022)
Data ostatniej modyfikacji:
2023-07-06
Data dodania obiektu:
2023-02-01
Liczba wyświetleń treści obiektu:
80
Wszystkie dostępne wersje tego obiektu:
https://zbc.uz.zgora.pl/publication/77338
Wyświetl opis w formacie RDF:
Wyświetl opis w formacie OAI-PMH:
-
International Journal of Applied Mechanics and Engineering (IJAME)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 29 (2024)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 28 (2023)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 27 (2022)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 27, number 1 (2022)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 27, number 2 (2022)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 27, number 3 (2022)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 27, number 4 (2022)
- International Journal of Applied Mechanics and Engineering (IJAME), volume 27, number 4 (2022) - spis treści
- Joining of carbon steel AISI 1006 to aluminum alloy AA6061-T6 via friction spot joining technique
- Optimization of friction stir processing parameters of aluminum alloy reinforced with hybrid nanoparticles using the Taguchi method
- Strouhal number effects on dynamic boundary layer evolution over a wedge surface from initial flow to steady flow: analytical approach
- Influence of form defect on the mechanical behavior and stress intensity factor of shrink-fitted thick-walled cylinders
- Applying optimization techniques on cold-formed C-channel section under bending
- Heat transfer effects on carbon nanotubes along a moving flat plate subjected to uniform heat flux
- Visco-elastic fluid model in an inclined porous stenosed artery with slip effect and body acceleration
- The influence of thermal expansion on flow past an inclined accelerated sectional plate with persistent mass diffusion
- Computational approach to solving a layered behaviour differential equation with large delay using quadrature scheme
- Generalized plane waves in a rotating thermoelastic double porous solid
- Two-dimensional analysis of functionally graded thermoelastic microelongated solid
- An investigation of the suspension characteristics of the line model of the vehicle using the Taguchi method
- A method for comparison of large deflection in beams
- Effect of ultrasonic peening on mechanical properties of low carbon steel AISI 1020 TIG welding joints process
- Fabrication of a high wear resistance AA7075/AL2O3 composites via liquid metallurgy process
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 27, number 1 (2022)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 26 (2021)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 25 (2020)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 24 (2019)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 23 (2018)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 22 (2017)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 21 (2016)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 20 (2015)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 19 (2014)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 18 (2013)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 29 (2024)
| Nazwa wydania | Data |
|---|---|
| Fabrication of a high wear resistance AA7075/AL2O3 composites via liquid metallurgy process | 2023-07-06 |
