Obiekt
Tytuł: Optimization of friction stir processing parameters of aluminum alloy reinforced with hybrid nanoparticles using the Taguchi method
Współtwórca:
Tytuł publikacji grupowej:
Abstract:
This study deals with the selection of optimum parameters for friction stir processing of Al alloy 6061-T6 reinforced with a hybrid nanoparticle (B4C and SiO2) in terms of their effect on the mechanical properties (hardness, tensile strength, and wear resistance) using Taguchi method. This work was carried out under four parameters each one running in three levels; rotational speeds (800, 1000 and 1200) rpm, travel speeds (10, 20, and 30) mm/min, holes depth (2, 2.5, and 3) mm, and mixing ratio of (SiO2/B4C) nanoparticles (1/1, 1/2, and 1/3), using L9 (34) Taguchi orthogonal array. ; Tensile strength and microhardness tests were conducted to evaluate the mechanical properties, in addition to the wear resistance test which is carried out using a pin-on-disk device. The microstructure was examined by optical microscopy, field emission scanning electron microscopy, and x-ray diffraction analysis. ; It was found that the highest tensile strength (223) MPa at 1200 rpm rotational speed, 30 mm/min traverse speed, 2.5 mm holes depth, and 1/2 (SiO2/B4C) nanoparticles mixing ratio, the highest hardness reached is (155) HV, then decreases in the direction of thermomechanically affected zone (TMAZ), heat affected zone (HAZ), and the base material at (1200) rpm rotational speed, (30) mm/min linear speed, a hole depth of (2) mm and (1/3) mixing ratio of (B4C/SiO2) nanoparticles. ; The wear behavior was of a mild type or an oxidative type at low loads (5 N), which became severe or metallic wear at higher loads (20 N) at fixed sliding time and speed. The (ANOVA) table has been used to determine which parameter is the most significant using MINITAB software.
Wydawca:
Zielona Góra: Uniwersytet Zielonogórski
Format:
Identyfikator zasobu:
DOI:
Strony:
Źródło:
IJAME, volume 27, number 4 (2022)
Jezyk:
Licencja:
Licencja CC BY-NC-ND 4.0:
Prawa do dysponowania publikacją:
Biblioteka Uniwersytetu Zielonogórskiego
Kolekcje, do których przypisany jest obiekt:
- Zielonogórska Biblioteka Cyfrowa > Repozytorium > Jednostki organizacyjne > Wydział Mechaniczny
- Zielonogórska Biblioteka Cyfrowa > Repozytorium > Typy utworów > Artykuły
- Zielonogórska Biblioteka Cyfrowa > Repozytorium > Czasopisma naukowe i serie wydawnicze UZ > International Journal of Applied Mechanics and Engineering (IJAME)
- Zielonogórska Biblioteka Cyfrowa > Repozytorium > Czasopisma naukowe i serie wydawnicze UZ > International Journal of Applied Mechanics and Engineering (IJAME) > International Journal of Applied Mechanics and Engineering (IJAME) (2022)
Data ostatniej modyfikacji:
2023-07-06
Data dodania obiektu:
2023-02-01
Liczba wyświetleń treści obiektu:
73
Wszystkie dostępne wersje tego obiektu:
https://zbc.uz.zgora.pl/publication/77325
Wyświetl opis w formacie RDF:
Wyświetl opis w formacie OAI-PMH:
-
International Journal of Applied Mechanics and Engineering (IJAME)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 29 (2024)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 28 (2023)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 27 (2022)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 27, number 1 (2022)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 27, number 2 (2022)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 27, number 3 (2022)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 27, number 4 (2022)
- International Journal of Applied Mechanics and Engineering (IJAME), volume 27, number 4 (2022) - Contents
- Joining of carbon steel AISI 1006 to aluminum alloy AA6061-T6 via friction spot joining technique
- Optimization of friction stir processing parameters of aluminum alloy reinforced with hybrid nanoparticles using the Taguchi method
- Strouhal number effects on dynamic boundary layer evolution over a wedge surface from initial flow to steady flow: analytical approach
- Influence of form defect on the mechanical behavior and stress intensity factor of shrink-fitted thick-walled cylinders
- Applying optimization techniques on cold-formed C-channel section under bending
- Heat transfer effects on carbon nanotubes along a moving flat plate subjected to uniform heat flux
- Visco-elastic fluid model in an inclined porous stenosed artery with slip effect and body acceleration
- The influence of thermal expansion on flow past an inclined accelerated sectional plate with persistent mass diffusion
- Computational approach to solving a layered behaviour differential equation with large delay using quadrature scheme
- Generalized plane waves in a rotating thermoelastic double porous solid
- Two-dimensional analysis of functionally graded thermoelastic microelongated solid
- An investigation of the suspension characteristics of the line model of the vehicle using the Taguchi method
- A method for comparison of large deflection in beams
- Effect of ultrasonic peening on mechanical properties of low carbon steel AISI 1020 TIG welding joints process
- Fabrication of a high wear resistance AA7075/AL2O3 composites via liquid metallurgy process
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 27, number 1 (2022)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 26 (2021)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 25 (2020)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 24 (2019)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 23 (2018)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 22 (2017)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 21 (2016)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 20 (2015)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 19 (2014)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 18 (2013)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 29 (2024)
